Slab Lifting in Dallas Fort Worth: Why Some Homes Need Piers Outside and Foam Inside
On the job in the photo above, our polyurethane foam team was inside the house lifting the interior slab while our steel pier crew lifted the outside of the foundation.
Slab lifting means raising a concrete slab that has settled. On a house, that slab is the foundation itself: a deep beam around the outside edge, often with more beams running under the interior, and a thinner floor slab between them. Around Dallas Fort Worth, where so many homes sit on a slab over clay that swells and shrinks, the edge and the middle of that slab do not always move together. When both have dropped, a proper repair takes two methods, and the timing of the two lifts matters just as much as the methods.
What Was Going On in the Photo
The trailer at the curb holds our foam lifting equipment, and the hose across the driveway runs to the crew lifting inside. The white utility truck parked in front of the trailer belonged to the same job. The house and the pier crew working along its foundation are out of the frame.
Two crews at one house is not a scheduling accident. The repair plan for that house called for steel piers under the outside beam and foam under the interior slab, with both crews lifting at the same time so that neither side would hold the other back.
Slab Lifting for a House Is Not the Same as Leveling a Driveway
People use the words slab lifting for two different jobs. One is raising a driveway, patio, sidewalk, or pool deck that has sunk. That is concrete leveling, and it usually takes one method: foam injected under the concrete. Our guide to sinking concrete repair compares the options for that kind of work.
The other job is lifting the slab your house sits on. That slab carries the walls, the roof, and everything inside, and it is tied into the beam around its edge. Lifting it is part of house leveling, and it is the kind of slab lifting this article is about. A driveway can come up on its own. A house slab has to come up as one connected piece, which is where the second method and the timing come in.
Why a DFW Slab Can Drop at the Edge and in the Middle
The soil under the outside edge of a house and the soil under the middle live very different lives. PTI, the institute whose slab on ground design manual many engineers use on expansive clay sites, describes an edge moisture variation distance: a band of soil under the edge of a slab where moisture changes with wetting and drying around the perimeter. When the soil at the edges is drier than the soil in the center, engineers call it center lift. When the edges are wetter, they call it edge lift.
That is the drought and swell cycle described in engineering terms. A long North Texas summer pulls water out of the clay along the outside of the house first, and the edge of the slab drops with it. Roots from a large tree near the house can pull that drying farther in under the slab on that side. A wet fall can swell that same clay back up. Our page on North Texas soil explains why the clay across much of the metroplex moves so much, and some parts of the area sit on Eagle Ford shale, which brings problems of its own.
Soil beneath the center of a house is shaded from sun and rain, so its moisture changes more slowly, and when it does change, the cause is often under the house. A drain line leaking under the floor can soften the soil or wash it away, although in clay a leak can also make the soil swell, which is covered below. Fill dirt that was not compacted well when the lot was built up can settle over time. Softened soil, washed out soil, and settling fill can each leave a low spot in the middle of the house that has nothing to do with what is happening at the edge.
So a single house can have a corner that dropped during a dry summer and a hallway that sank over a leak, and those are two different problems that need two different fixes.
There is one more possibility to rule out before anyone talks about lifting. Clay that swells after a leak or a long wet spell can push part of a slab up, which our slab foundation repair page calls upheaval. A floor that looks low in one room may really be high in the next one. Lifting the wrong area makes the problem worse, which is why a foundation inspection with floor elevation readings comes before any repair plan.
The Job Exterior Steel Piers Do
Steel push piers go in along the outside beam. At each pier location, the crew digs down to the footing, mounts a steel bracket to it, and drives pier sections through the active clay until they reach load bearing strata. How deep that is varies a lot across the area, and our guide to foundation piers and bedrock depth in DFW covers why. Once the piers are set, the edge of the house is raised on them, and from then on it bears on steel rather than on shifting clay. The process is laid out step by step on our steel pier foundation repair page, and our comparison of steel piers vs concrete piers explains why we use steel. Where a structure is too light to drive push piers against, helical piers are screwed into the ground instead.
What exterior piers do not do is reach the middle of the slab. They hold up the edge. If the floor in the center of the house has dropped over a void, setting piers around the outside will not bring that floor back up, and it will not fill the space underneath it.
What Foam Lifting Does Beneath the Floor
Inside, our foam team drills a pattern of small holes in the floor and injects a two part polyurethane beneath the slab. As the two parts mix, the material expands. First it fills gaps, then it firms up loose soil, and when there is nowhere left for it to go, it starts raising the concrete. The cured foam is very light, so it adds little weight to soil that is already having trouble carrying the house.
Foam has limits. It holds the slab up on whatever soil is already under it, and it cannot hand the load down to firmer strata the way a pier can. When the edge of a house has settled, foam works next to piers, not in place of them.
Many newer homes around the metroplex are built on post tension slabs, and those need extra care inside. The steel tendons in a post tension slab are pulled tight after the concrete hardens, and a drill bit that strikes one can damage it. The injection holes have to be planned around where the tendons run. If you are not sure what kind of slab your home has, our article on post tension slab problems explains how to tell.
Why Our Crews Lift the Edge and the Middle Together
A slab is stiff, but it can only flex so far before it cracks. The beam around the edge and the floor in the middle are tied together, often poured as one piece, so whatever happens to one part pulls on the other.
Suppose the pier crew lifts the edge first while the middle is still low. As the outside rises, the center lags behind, and the slab starts to bow between the two. The crew has to stop before that bow cracks the floor or the tile, which can be well short of where the piers could have taken the edge. If the foam team comes back the following week, the middle can rise only as far as that early stopping point.
Turn it around and the result is the same. The foam team raises the middle while the edges sit low, and the slab arches over them until that lift has to stop too. Piers installed later can only bring the edge up to meet it.
Either way, recovery (the share of the settlement a repair wins back) ends up limited on both sides. Lifting in tandem is how our crews avoid that. The pier crew raises the edge a little, the foam team brings the middle up to match, and they repeat in small steps until the slab reaches the goal, so no part of the floor gets far ahead of the rest. NCFI, a polyurethane manufacturer, lays out the same sequence: lift the outside about an inch, raise the inside to match with foam, and repeat. It also notes that raising a slab on piers opens gaps beneath it, and those gaps need filling, which helps explain why the two methods show up together so often.
A full return to the original elevation is not always possible or wise. Cabinets, tile, drywall, and door frames have adjusted to years of movement, and a lift that ignores that can cause new damage. The goal is the most recovery the house can safely take, and the elevation readings taken before and during the lift are what decide it.
Mixed Foundations and Other Combinations Around the Metroplex
Piers and foam are one pairing. These come up often in North Texas too:
- Pier and beam homes with a slab section. Many older Dallas neighborhoods are full of pier and beam homes with a crawl space underneath, and some of those houses have a slab addition or a back room poured later. One house can then need crawl space repair under the original part and piers or foam under the slab part, and the floors where the two sections meet must finish at the same height. Our pier and beam foundation repair page explains the crawl space side of that work.
- Piers and drainage. A lot of flat North Texas lots let roof water and sprinkler runoff sit against the foundation. Piers correct the settlement, and drainage solutions such as French drains and tight lines deal with the water that caused it.
- Piers and slope repair. On a lot that falls away from the house, erosion can undercut the foundation. Piers stabilize the house, but as our article on slope failure foundation repair explains, the slope still needs its own repair.
- Newer homes on built up pads. Fill under a new slab can compress unevenly, so the edge and the middle of a newer home can settle by different amounts. Our article on helical piers for new construction explains why building pads settle.
When One Repair Is Split Between Two Companies
Plenty of foundation companies focus on one method. Some install piers and nothing else. Some do foam and nothing else. That works fine until a house needs both. At that point, some will take on the full job anyway and bring in a second company for the half they cannot do.
The risks are easy to miss when you are reading an estimate:
- Two schedules. Lifting in tandem needs both crews on site at the same time, working from the same readings. Two companies running two calendars can make that hard.
- Two sets of priorities. The hired company may never hear what you were told during the sales visit or what matters most to you about the finished floors.
- Two answers when something is off. If a door still sticks after the work, each company can say the other one caused it.
- Two warranties. Coverage can be written differently for different parts of the same house, and a gap between the two may not show up until you need the coverage.
None of that means every subcontracted job goes wrong. It means you should know who is doing each part of the work before anything starts.
How Level Home Handles a Combined Lift in DFW
At Level Home, both halves of a combined lift stay in house. Exterior steel piers, polyurethane foam lifting, crawl space repair, helical piers, and drainage solutions are all handled by our own crews, along with the other structural repairs a house may need. The crew lifting the outside and the crew lifting the inside both work for Level Home and are held to one standard of quality.
Because both crews are ours, a tandem lift does not depend on another company’s calendar. The team that measured the house plans the lift, the same readings guide both crews, and nobody has to coordinate across two businesses in the middle of the job. You can read more about our team and how we work.
Our processes are approved by engineering firms across Texas and Oklahoma, and we have never failed an engineer reinspection. Our team has been handling foundation repair for over 10 years. One company, one warranty, no concerns.
What to Ask Before You Sign a Repair Plan
If an estimate lists piers and foam, or any mix of repairs, these questions are worth asking:
- Does the plan address the edge, the middle, or both, and how did you decide?
- Will you take floor elevation readings before the lift, during it, and after it?
- Are the exterior and interior lifts scheduled for the same visit?
- If my home has a post tension slab, how will you place the injection holes?
- What is being done about the cause, such as drainage, a plumbing leak, or grading?
- Who will be on site for each part, and do they all work for you?
- Who do I call if something is not right afterward, and is all of the work under one warranty?
Our page on foundation repair cost also covers what a good estimate should include.
The Short Version
- Slab lifting on a house is different from leveling a driveway. A house slab has to come up as one connected piece.
- In DFW, the edge of a slab and the middle can settle for different reasons: dry clay along the perimeter, and leaks or loose fill under the center.
- Exterior steel piers lift and support the edge. Foam fills gaps under the interior slab and raises it. Neither method can do the other’s job.
- Lifting both together, in small steps, lets each repair win back more of the settlement than either could on its own schedule.
- Post tension slabs need the injection holes planned around the tendons.
- Level Home crews handle piers, foam, crawl space work, and drainage themselves, so a single company plans the repair and answers for it.
Frequently Asked Questions
Is slab lifting the same as house leveling?
They overlap. House leveling usually describes the whole job of bringing a home back toward level, most often with piers under the outside beam. Slab lifting describes raising the slab itself, which can mean piers at the edge, polyurethane foam under the middle, or both. On a slab home in Dallas Fort Worth, a house leveling project may include slab lifting with foam when the interior has dropped too.
Why are my floors still uneven after piers were installed?
Piers along the outside lift and support the edge of the slab. If the middle of the house had also settled, or a void opened under it, the interior floor can stay low even after the piers are set. Floor elevation readings show where the low areas are. Depending on the cause, the fix may be foam under the slab, interior piers, or a plumbing repair before anything else.
Do post tension slabs need special care during slab lifting?
Yes. The steel tendons inside a post tension slab are held under tension, and drilling into one can damage it. Any holes for foam injection have to be placed with the tendons in mind. A post tension slab can still be lifted, but the plan has to account for how it was built.
Does every settled slab need both piers and foam?
No. Plenty of homes need only one. If the edge has dropped and the interior is sound, piers alone may be the right repair. If a void opened under one part of the floor and the edge has not moved, foam alone may be enough. Both are needed when the edge and the middle have each settled, and floor elevation readings are what show that.
Can a pier and beam house with a slab addition be repaired in one project?
Yes, when one plan covers both parts. The crawl space side may need new supports, shims, or moisture control, and the slab side may need piers, foam, or both. The two sections share a floor line, so they should be planned and adjusted together until they meet at the same height.
How do I find out what my slab needs?
Start with a foundation inspection that includes floor elevation readings across the whole house, not just the rooms with cracks. That shows whether the edge, the middle, or both have moved, and whether any part has heaved instead of settling. A foundation inspection from our Dallas Fort Worth team is free.
Schedule a Free Foundation Inspection in Dallas Fort Worth
Cracks in the brick, a dip in the hallway, or a door that suddenly sticks are all worth a closer look. Schedule a free foundation inspection. Our team will measure your home, walk you through what we find, and explain whether it needs one repair method or more than one. Financing options are available. Call (972) 217-4820 or contact us online.


Leave a Reply